Easy Curved Upholstered Headboard For Under $25!

Pin It
Hi everyone! I had a great opportunity today to demonstrate my favorite go-to DIY project for any bedroom on Studio 5 (a local show here in Utah for those of you who aren't from around here :) ). You may remember the white headboard that I made for a guest bedroom (in this post). Well, I decided to amp it up a bit and make one with a little curve and with some great color.
DIY $25 Curved Upholstered Headboard
The measurements for this are for a twin headboard. It is 40" wide and 60" tall. If you want to make this for any size bed, you can follow this post here for further details on how to make it taller and wider, but as a rule of thumb for measurements, just make sure that the plywood and fabric go at least 2 inches below the top of the mattress and 1" or 2" past each side...and the ceiling is the limit for the height!

Here are the supplies you need:
Plywood cut to size (I used 3/8")
Marker and string
Batting
Staple gun
Fabric
Hot Glue Gun
Buttons

First step: To make the curve on each side, tie the string to your marker and secure the string to one of the top corners of the plywood...remember this mark on the string. Trace a curve onto the plywood. Now remember the angle you used with your hand when you traced it, and do the exact same thing to the opposite side. To make it easy, just make the marker go straight up and down :) ...doesn't doing this remind you of junior high??? lol
DIY $25 Curved Upholstered Headboard
 Step 2: Get your jigsaw and cut out the curve. Make sure all safety measures are in place before you do this :)
DIY $25 Curved Upholstered Headboard
 Step 3: Okay. Now it's time for your batting. You can fill this whole thing with batting if you really wish, or if you want to go cheap (like me) you can just do the part that the head will hit. I placed about 4 layers of batting on this. Secure it in place with a staple gun and staples.

DIY $25 Curved Upholstered Headboard
 You can see here where I decided to place the batting:
DIY $25 Curved Upholstered Headboard
 Step 4: Place your fabric on a flat surface upside down. Place your plywood on top of it with the batting towards the fabric. Cut the fabric around the plywood so it will fold over by 2-4 inches. Start folding the fabric over the plywood and securing with a staple gun. If you have a design on your fabric, try to make sure you are securing your fabric following the pattern of the fabric. So, find a motif or point on your fabric that repeats, and make that point be the one that lines up on the edge. Make sure you following this rule all the way around. If you don't, you may just turn it over to find a crooked mess :) Of course each edge will be a different repeating point more than likely.
DIY $25 Curved Upholstered Headboard
 For the curves, you'll find that it is impossible to fold fabric over if you leave it square. So, cut the fabric about 2 inches away from the plywood following the curve.
DIY $25 Curved Upholstered Headboard
 Step 5: Now decide how many buttons you want. I like to have three over and three high. So, divide your board and find where your marks should go. If you have a pattern, once again, this makes it super easy :) You can just  put the buttons on the same point in design. I believe I did mine every 10 inches. Just make sure your marks are on top of the batting. This will give you the great tufted look. And make sure that the middle mark is directly in the middle of the headboard; so for this headboard it will be at 20".
DIY $25 Curved Upholstered Headboard
  Once you are done stapling. Pick your buttons. I like to use ones that don't have holes, or at least noticeable holes.
DIY $25 Curved Upholstered Headboard
 Now use your hot glue gun and glue them straight onto the staple.
DIY $25 Curved Upholstered Headboard
 And there you have it! This whole process shouldn't take more than an hour to do. I'm loving the color of this fabric by the way. It's from Hobby Lobby in the duck clothe section. Just remember when you use fabric with pattern on it, you need to make sure it won't be going on sideways, and if it does it won't look bad. Most fabrics range from 45" to 54", and this headboard is 60" tall, so you will have to have the fabric go the opposite way than the pattern more than likely since most patterns go the other way. I hope that all made sense :)
DIY $25 Curved Upholstered Headboard
The cost of this project:
Plywood - (whole piece cost $9) So probably about $6
Batting - $6
Fabric - $10
Buttons - $2

Under $25!
To make this cheaper, you can use an old comforter/blanket for the batting and of course use cheaper fabric like a sheet :) And yes, I used a coupon for everything on here except the plywood.

Here's the video segment I did about this headboard. It offers some good tips too :)

8 comments

  1. I'm seriously obsessed with everything that you do! This is definitely going on my "DIY Projects To Do" list. Thanks for sharing :)

    ReplyDelete
  2. Great headboard and I love the fabric and the style. Stunning.

    ReplyDelete
  3. I love this easy and cheap headboard DIY. Please continue to do what you do, and show it to us. I'm in need of cheap DIY projects like this :)

    ReplyDelete
  4. this is simply gorgeous, love it! Thanks for linking up to Inspire Me Monday :) XO

    ReplyDelete
  5. Absolutely love the headboard and the choice of fabric combinations! Thanks for the tutorial and linking it up to our Inspire Me Monday! I can see Kristin already beat me here! Ha!

    ReplyDelete
  6. Love your headboard!! I'm featuring it tomorrow in my Friday Features... apparently a big hit with us Inspire Me Monday gals. Thanks for linking up!

    ReplyDelete
  7. How about using a small screw and small washer to glue the button on as opposed to the iffy staple?

    ReplyDelete

happy DIYing! Alicia